Modifications & Upgrades

Discussion List

• How to compile Marlin 2.0 firmware for JGAurora A5 - Community Firmware (2.0H) - 2021 Guide

  Announcement 2.6K views 7 comments 0 points Most recent by Samuel Pinches July 2021
• Check out the wiki for many upgrades for your A5 or A3S printer...

  Announcement 2.8K views 5 comments 0 points Most recent by Eye May 2021
• E3D V6 hotend conversion for A5

  Announcement 1.1K views 4 comments 0 points Most recent by Jozko Remen December 2020
• Upgrade to TMC2208 Stepper Drivers

  Announcement 8K views 44 comments 0 points Most recent by Roger April 2020
• MKS PWC V2.0 auto off after printing end with A5

  Announcement 1.2K views 0 comments 0 points Started by coolt5 March 2020
• [Project] Upgrading the A5 to Direct Drive + full metal hotend + auto bed leveling for under 60$

  Announcement 6.8K views 27 comments 0 points Most recent by Samuel Pinches January 2020
• A5 - and what became out of it...

  Announcement 695 views 3 comments 0 points Most recent by Charly3 September 2019
• Important things to know regarding stepper upgrade with TMC 2130 with SPI

  Announcement 2.4K views 26 comments 0 points Most recent by Samuel Pinches April 2019
• The "quest" is over

  128 views 7 comments 0 points Most recent by Eye April 13
• Successfully upgraded to marlin 2.1 and TFT28 to BigTreeTech for using TMC2209 Drivers

  42 views 0 comments 0 points Started by Feepro January 16
• New Hotend/Temperature sensor

  71 views 1 comment 0 points Most recent by rhaub101 April 2022
• Shell finished

  38 views 0 comments 0 points Started by Matt December 2021
• v6 steel?

  57 views 13 comments 0 points Most recent by Gandy October 2021
• Hot end heatsink replacement

  89 views 2 comments 0 points Most recent by noobmaker October 2021
• JGAurora A5 - Linear rail X - MGN12 - H

  896 views 8 comments 0 points Most recent by Furba June 2021
• MKS TFT28 V4.0 Flashing Problems

  56 views 1 comment 0 points Most recent by Samuel Pinches June 2021
• octoprint problem

  151 views 1 comment 0 points Most recent by Samuel Pinches June 2021
• Firmware Mariln 1.1.9C for JGaurora A3S with BLTOUCH

  212 views 1 comment 0 points Most recent by Samuel Pinches May 2021
• Makerbase mkstft28 replacement questions?

  65 views 2 comments 0 points Most recent by mrfalk May 2021
• JG aurora a 5 flexible cam holder thingy

  57 views 2 comments 0 points Most recent by Eye May 2021
• Which Cooling Duct to choose?

  1.8K views 18 comments 0 points Most recent by Eye April 2021
• Building a Box / Scrap upecyling ;)

  166 views 0 comments 0 points Started by Eye April 2021
• cutting cables

  177 views 16 comments 0 points Most recent by Eye April 2021
• Problem with i Box

  563 views 15 comments 0 points Most recent by ChAoS March 2021
• Bowden tube fittings?

  385 views 5 comments 0 points Most recent by Eye March 2021
• A5 Heating Problem

  63 views 2 comments 0 points Most recent by Samuel Pinches March 2021
• Tinkering Thread: Marlin Firmware for the A5 main board (1.1.8C --> 2.x) with LCD firmware (v.3.03)

  143 views 8 comments 0 points Most recent by Eye February 2021
• Installing a Duet in the A5

  152 views 2 comments 0 points Most recent by Sergey February 2021
• JGAurora A5 Thermistor

  220 views 2 comments 0 points Most recent by michalko99 February 2021
• Hotbed 310x310 24v question?? Help!!

  110 views 4 comments 0 points Most recent by Erwaly January 2021
• JGAurora A5 drivers without potentiometers

  467 views 14 comments 0 points Most recent by Matt January 2021
• Still troubles with z-axis

  131 views 12 comments 0 points Most recent by Matt January 2021
• Looking to upgrade some stuff

  107 views 3 comments 0 points Most recent by michalko99 January 2021
• Where to route a bed probe sensor cable on the A5?

  39 views 2 comments 0 points Most recent by noobmaker January 2021
• Replacement linear bearings

  522 views 7 comments 0 points Most recent by michalko99 January 2021
• Marlin 2.0 and 32bit board for JGAURORA A5. It is workable?

  1.8K views 22 comments 0 points Most recent by Gandy January 2021