Modifications & Upgrades

Discussion List

• Extruder Replacement Options?

  672 views 0 comments 0 points Started by Flashfyr3 January 2020
• Cold End Fan Controller Upgrade

  2.1K views 4 comments 0 points Most recent by Valéry Lopez January 2020
• GOODBYE MRS. BOWDEN

  2.6K views 29 comments 0 points Most recent by Helpstone January 2020
• How to add Driver cooler / Board cooler for TMC 2208

  112 views 1 comment 0 points Most recent by Gandy December 2019
• Z Wobble

  1.3K views 23 comments 0 points Most recent by poikilos November 2019
• Some experience with Titan Aero Extruder All metal enhanced on A5 printers

  350 views 1 comment 0 points Most recent by AJ_CADDone November 2019
• I broke the pins of filament sensor on my JGAURORA A5

  81 views 0 comments 0 points Started by coolt5 November 2019
• Falshing firmware via st-link

  159 views 5 comments 0 points Most recent by taxidude November 2019
• best encloser I can think of for JGAURORA A5 that uses the printer frame to hold it :)

  441 views 2 comments 0 points Most recent by coolt5 October 2019
• Custom Firmware Upgrade

  255 views 1 comment 0 points Most recent by Samuel Pinches October 2019
• Problems after TMC2130 drivers installation.

  256 views 1 comment 0 points Most recent by Claudiu84 October 2019
• Noise from the Y axis

  2.2K views 18 comments 0 points Most recent by MikeG183 September 2019
• V 2.0 Firmware

  347 views 1 comment 0 points Most recent by Samuel Pinches September 2019
• Bed Shifting

  98 views 2 comments 0 points Most recent by Charly3 September 2019
• New heatbreak, everything to short

  572 views 15 comments 0 points Most recent by Samuel Pinches August 2019
• extruder motor

  82 views 1 comment 0 points Most recent by Laser8302 August 2019
• CAD model of the hot-end

  563 views 3 comments 0 points Most recent by LucasS11 August 2019
• Capricorn tubing kit

  757 views 9 comments 0 points Most recent by Laser8302 August 2019
• When to not use a Harden Steel/Tungsten Nozzle ?

  95 views 3 comments 0 points Most recent by Samuel Pinches August 2019
• JGAurora A5 with cloned BGM Extruder, 3DTouch & 0.6 mm nozzle

  264 views 0 comments 0 points Started by Jozko Remen August 2019
• On the go to install tl_smoothers

  109 views 14 comments 0 points Most recent by Samuel Pinches August 2019
• JGAURORA A5 ALL AXIS ARE NOT MOVING AFTER REFLASHING MARLIN 1.1.8C(( SOLVED ))

  347 views 38 comments 0 points Most recent by Laser8302 July 2019
• Full bed replacement?

  205 views 17 comments 0 points Most recent by Laser8302 July 2019
• New MKS TFT28 V4.0 for LCD replacement - leveling issue.

  240 views 5 comments 0 points Most recent by kureka July 2019
• JGAurora A5 stopping mid print without error even when pronterface is running and monitoring ??

  292 views 1 comment 0 points Most recent by coolt5 July 2019
• Upgrade bearings for x and y axis

  1.7K views 68 comments 0 points Most recent by ufodoctor3 July 2019
• A3S Internal Power Supply.

  36 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• thyrister was bad and ordered a new A5 hotbed, but the new bed has 6 pins instead of 4 whats next?

  61 views 3 comments 0 points Most recent by gary74 June 2019