Getting Started & Troubleshooting

Discussion List

• Y axis issues / bed nut impacting on base

  91 views 1 comment 0 points Most recent by jollypike July 2018Getting Started & Troubleshooting
• full size prints 300mm x 300mm x 300mm , speed ???

  100 views 3 comments 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• Extruder preheat sets to 0 when trying to print

  78 views 1 comment 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• Heated bed not working

  216 views 13 comments 0 points Most recent by AETEK July 2018Getting Started & Troubleshooting
• Is this Layer Shift? Recommendations on how to fix?

  661 views 1 comment 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• A5 Nozzle temperature reads -15 degrees

  696 views 23 comments 0 points Most recent by dandan July 2018Getting Started & Troubleshooting
• can't save bed leveling data

  626 views 2 comments 0 points Most recent by davidtriune July 2018Getting Started & Troubleshooting
• min temp reached error

  685 views 8 comments 0 points Most recent by Samuel Pinches November 2019Getting Started & Troubleshooting
• cleaning the bed

  589 views 1 comment 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• problems with Y and Z axes

  233 views 4 comments 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• Why do the thermistor inputs break sometimes?

  1.4K views 5 comments 0 points Most recent by AETEK June 2018Getting Started & Troubleshooting
• Z-axis not moving at all

  1.6K views 20 comments 0 points Most recent by seafian July 2018Getting Started & Troubleshooting
• New A5 Reboots when preheating bed for leveling

  162 views 11 comments 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• Keep your eyes open when filament buying

  188 views 3 comments 0 points Most recent by lsh60 September 2018Getting Started & Troubleshooting
• Heatbreak for A5

  833 views 2 comments 0 points Most recent by AETEK June 2018Getting Started & Troubleshooting
• PETG prints stops after a while

  637 views 8 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Left z axis lead screw gets stuck

  1.1K views 2 comments 0 points Most recent by DIYglenn September 2018Getting Started & Troubleshooting
• Extruder and Bed same temp problems

  576 views 47 comments 0 points Most recent by Ophiocos June 2018Getting Started & Troubleshooting
• Bed Temp after Printing

  210 views 7 comments 0 points Most recent by Samuel Pinches June 2018Getting Started & Troubleshooting
• Carbon fiber filament

  695 views 19 comments 0 points Most recent by cs2000 April 2019Getting Started & Troubleshooting
• JGAURORA A5 - A very disappointing 3D Printer

  3.1K views 37 comments 0 points Most recent by netzmark November 2018Getting Started & Troubleshooting
• Possible to print without filament?

  75 views 2 comments 0 points Most recent by Hevilp June 2018Getting Started & Troubleshooting
• Stepper Driver: Y driver error detected

  166 views 2 comments 0 points Most recent by Hevilp June 2018Getting Started & Troubleshooting
• Can't level bed high enough

  1.4K views 15 comments 0 points Most recent by Samuel Pinches March 2020Getting Started & Troubleshooting
• print pop off plate during resume on A5

  196 views 4 comments 0 points Most recent by enochroot June 2018Getting Started & Troubleshooting