Getting Started & Troubleshooting

Discussion List

• Printer started smoking after 1st use

  129 views 16 comments 0 points Most recent by Wingnut August 2018Getting Started & Troubleshooting
• Another bed heating Problem

  445 views 10 comments 0 points Most recent by Samuel Pinches August 2018Getting Started & Troubleshooting
• Can’t print from flash drive

  221 views 2 comments 0 points Most recent by rhaub101 July 2018Getting Started & Troubleshooting
• Bed not heating up!!! Where can I get another one? A5

  436 views 8 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• printer not connected

  350 views 2 comments 0 points Most recent by salesinteract July 2018Getting Started & Troubleshooting
• Hot swap filaments mid print.

  299 views 3 comments 0 points Most recent by Richy_T August 2019Getting Started & Troubleshooting
• Poor printing quality

  154 views 2 comments 0 points Most recent by Flo1988 October 2018Getting Started & Troubleshooting
• Need Help with Troubleshooting Blobs

  276 views 7 comments 0 points Most recent by nottub August 2018Getting Started & Troubleshooting
• Clogging at the beginning of the heat break

  76 views 2 comments 0 points Most recent by Hevilp July 2018Getting Started & Troubleshooting
• Blower Fan Short?

  196 views 9 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Short circiut on heat element - board broken?

  95 views 6 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Automatically paused during a build?

  506 views 21 comments 0 points Most recent by coolt5 July 2019Getting Started & Troubleshooting
• Money Cat from USB fine, but nothing else sticks to bed

  224 views 3 comments 0 points Most recent by Alex October 2018Getting Started & Troubleshooting
• Errors in the documentation for the MKS GEN_L 1.0 motherboard (EXP1 & EXP2)

  556 views 2 comments 0 points Most recent by AETEK July 2018Getting Started & Troubleshooting
• Can't move after manually stopped the build process?

  120 views 8 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• the hot bed does not heat

  118 views 1 comment 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Broken steppers?

  398 views 12 comments 0 points Most recent by Jari Christopherson July 2018Getting Started & Troubleshooting
• Warning: Heated Bed Power Clamps

  997 views 10 comments 0 points Most recent by Alex October 2018Getting Started & Troubleshooting
• A5 LCD flashing "Booting..." and beeping at the same time.

  146 views 1 comment 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Help with print settings

  746 views 1 comment 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Bed Leveling Screws/Springs - Very Tight... stripping knobs

  368 views 2 comments 0 points Most recent by Nitro66215 July 2018Getting Started & Troubleshooting
• Temp froze on screen

  69 views 1 comment 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Distance between nozzle and heatbed after leveling

  1.1K views 64 comments 0 points Most recent by cybercow November 2018Getting Started & Troubleshooting
• not extruding anything

  1.4K views 11 comments 0 points Most recent by seafian July 2018Getting Started & Troubleshooting
• Reverse axis and general troubleshooting TMC2130 v1.1

  504 views 2 comments 0 points Most recent by Ophiocos July 2018Getting Started & Troubleshooting
• Nozzle way off the bed after nozzle change

  177 views 4 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• a few questions

  68 views 0 comments 0 points Started by nach00 July 2018 Getting Started & Troubleshooting
• Bed leveling mesh not applying

  347 views 10 comments 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• Absolute tangled mess misprints... what’s up!?

  182 views 1 comment 0 points Most recent by Samuel Pinches July 2018Getting Started & Troubleshooting
• First calibration steps

  1.1K views 8 comments 0 points Most recent by Jozko Remen August 2018Getting Started & Troubleshooting