Getting Started & Troubleshooting

Discussion List

• NOT EXTRUDING

  271 views 4 comments 0 points Most recent by Michael Horgan October 2018Getting Started & Troubleshooting
• A5 won’t implement mesh the previous level

  93 views 2 comments 0 points Most recent by Simon September 2018Getting Started & Troubleshooting
• Y axis stuttering

  573 views 6 comments 0 points Most recent by stevema October 2018Getting Started & Troubleshooting
• Extruder motor question

  82 views 2 comments 0 points Most recent by rhaub101 September 2018Getting Started & Troubleshooting
• weird layer issue...

  102 views 1 comment 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Calibration cube to big

  364 views 1 comment 0 points Most recent by Gonzo September 2018Getting Started & Troubleshooting
• printing in the bottom left corner (a5)

  99 views 1 comment 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• A5 bed heater cycling

  151 views 5 comments 0 points Most recent by Jamal3f November 2018Getting Started & Troubleshooting
• Change max retraction speed in community firmeare

  243 views 1 comment 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Loose x-axis coupling and other annoyances

  163 views 1 comment 0 points Most recent by delirii September 2018Getting Started & Troubleshooting
• PETG: unable to print a perfect object

  1.9K views 9 comments 0 points Most recent by compman2 December 2018Getting Started & Troubleshooting
• Printing Hatchbox PLA issues

  433 views 4 comments 0 points Most recent by compman2 October 2018Getting Started & Troubleshooting
• Heating failed, Heatbed

  181 views 10 comments 0 points Most recent by Tim92 September 2018Getting Started & Troubleshooting
• Printer Stopped Working - How To Troubleshoot?

  171 views 1 comment 0 points Most recent by effendoodle October 2018Getting Started & Troubleshooting
• A5 bed replacement

  244 views 0 comments 0 points Started by sasa September 2018 Getting Started & Troubleshooting
• Strange underextrusion after power failure

  210 views 6 comments 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• Problem with Z axis

  1.8K views 8 comments 0 points Most recent by jsanch May 2020Getting Started & Troubleshooting
• Change filament mid print

  1.1K views 4 comments 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Print Resume Feature

  348 views 2 comments 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Wobbely wobbely - need advice on....no clue what I'm looking at...

  144 views 3 comments 0 points Most recent by wolph42 September 2018Getting Started & Troubleshooting
• My A5 stopped in the middle of a print, no problems found.

  83 views 0 comments 0 points Started by DIYglenn September 2018 Getting Started & Troubleshooting
• Cura - fine setting - no bed adhesion

  592 views 2 comments 0 points Most recent by wolph42 September 2018Getting Started & Troubleshooting
• Spring supports....opinions?

  277 views 16 comments 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Please Diagnose my symptoms

  262 views 10 comments 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Extruder clicking noise at retracts and when changing filament

  743 views 5 comments 0 points Most recent by allengregoryiv September 2018Getting Started & Troubleshooting
• What is the screw size that holds the extruder fan duct in place?

  246 views 2 comments 0 points Most recent by Samuel Pinches September 2018Getting Started & Troubleshooting
• Printing is automatically paused - need HELP!

  714 views 5 comments 0 points Most recent by hver September 2018Getting Started & Troubleshooting