Getting Started & Troubleshooting

Discussion List

• Best way to clean pla off extruder

  538 views 8 comments 0 points Most recent by beata April 2019Getting Started & Troubleshooting
• How do I replace the threaded filament tube that holds the print head?

  540 views 16 comments 0 points Most recent by Sparks May 2019Getting Started & Troubleshooting
• psu fan, start when hot

  57 views 2 comments 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• Part cooling fan not turning ON with Cura 4.0?

  583 views 7 comments 0 points Most recent by chilman408 March 2019Getting Started & Troubleshooting
• PETG printing = a lot of frustrations

  710 views 9 comments 0 points Most recent by Laser8302 April 2019Getting Started & Troubleshooting
• User Manual Support Guide for JGAurora A5

  820 views 0 comments 0 points Started by Samuel Pinches March 2019 Getting Started & Troubleshooting
• WTF!!!

  83 views 1 comment 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• Noob question and did I just damage my heatbed?

  248 views 6 comments 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• Feet broke off, also firmware flashing.

  64 views 16 comments 0 points Most recent by cs2000 March 2019Getting Started & Troubleshooting
• Baby stepping save?

  80 views 1 comment 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• Micro-swiss + PETG = failed prints?

  2.6K views 12 comments 0 points Most recent by Laser8302 August 2019Getting Started & Troubleshooting
• change filament gcode script

  630 views 12 comments 0 points Most recent by hanzfranz March 2019Getting Started & Troubleshooting
• Offset printout to the right

  75 views 1 comment 0 points Most recent by Der_Muck March 2019Getting Started & Troubleshooting
• Bed heater stopped working

  229 views 20 comments 0 points Most recent by Der_Muck March 2019Getting Started & Troubleshooting
• Kasey

  183 views 1 comment 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• Bed Adhesion/Leveling, need to print wheelchair for dog.

  137 views 14 comments 0 points Most recent by Samuel Pinches July 2019Getting Started & Troubleshooting
• Print suddenly stops with no sond nor message (A3-S)

  304 views 9 comments 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• Tuning stock stepper drivers

  52 views 2 comments 0 points Most recent by rhaub101 March 2019Getting Started & Troubleshooting
• Run Out Sensor (How to Actually use It)

  331 views 4 comments 0 points Most recent by cs2000 March 2019Getting Started & Troubleshooting
• Filament sensor problem

  1.6K views 8 comments 0 points Most recent by Samuel Pinches September 2019Getting Started & Troubleshooting
• A5 randomly crashes with the message "closing mashine ...."

  333 views 10 comments 0 points Most recent by Samuel Pinches March 2019Getting Started & Troubleshooting
• TMC 2208 snipped pin issue

  97 views 2 comments 0 points Most recent by itisnot_me March 2019Getting Started & Troubleshooting
• Bed Adhesion and PLA Curling

  1.3K views 8 comments 0 points Most recent by Samuel Pinches July 2019Getting Started & Troubleshooting