Toggle navigation
Categories
Discussions
Activity
🔨Firmware
🧰Starter Kit
💡Wiki
🛒Shop
Sign In
Home
Please note: the forum is closed.
No new user registrations are accepted. For more info, please click here.
Getting Started & Troubleshooting
Archives for July 2019
Next
Discussion List
you thoughts on the best slicer program to run the a5s on ?
133
views
2
comments
0
points
Most recent by
chainbreaker2012
August 2019
Getting Started & Troubleshooting
What may be the cause for a rough bottom layer?
293
views
12
comments
0
points
Most recent by
WidgetElgie
November 2019
Getting Started & Troubleshooting
What causes gaps in print
53
views
4
comments
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
How to setup the cooling fan to shut off when the print has completed?
271
views
3
comments
0
points
Most recent by
WidgetElgie
July 2019
Getting Started & Troubleshooting
first layer to thin after leveling
209
views
12
comments
0
points
Most recent by
chainbreaker2012
July 2019
Getting Started & Troubleshooting
Beginner Questions - How to Optimize Print Speeds
842
views
4
comments
0
points
Most recent by
WidgetElgie
July 2019
Getting Started & Troubleshooting
Repairing my Mom's Last Christmas Gift Help?
48
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
Slicer Supports Settings
114
views
0
comments
0
points
Started by
SomeoneYouLike
July 2019
Getting Started & Troubleshooting
Unable to launch printing from se card
89
views
2
comments
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
So this happened
91
views
2
comments
0
points
Most recent by
rhythmdave
July 2019
Getting Started & Troubleshooting
printer unloading filament mid print
92
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
A5S touch screen blank
280
views
3
comments
0
points
Most recent by
John Buswell
July 2019
Getting Started & Troubleshooting
Here's a doozy for ya...A1, A5S, etc.
94
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
A1 custom community firmware and Octoprint
73
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
Edges of curves have flat spots
520
views
5
comments
0
points
Most recent by
mgrabow
July 2019
Getting Started & Troubleshooting
A5S Solutions and problems from a new A5S owner
307
views
4
comments
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
Odd issue - Bed Temp, Nozzle Temp and extruder all stop during the print
112
views
4
comments
0
points
Most recent by
Simulanon
July 2019
Getting Started & Troubleshooting
Please help
116
views
8
comments
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
A1 only fan working
73
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
New JGaurora A5 V4.0 board has new firmware with wifi?
317
views
5
comments
0
points
Most recent by
Scottmg
July 2019
Getting Started & Troubleshooting
Leveling with the points in the interface - Not moving across the x
36
views
0
comments
0
points
Started by
Spark
July 2019
Getting Started & Troubleshooting
A1 - Have to level it often
30
views
3
comments
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
getting printer into vase mode to print. (A5S) How is that done.
63
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
X axis terrible ratteling
88
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
A5S stops printing after printing the build adhesion
110
views
4
comments
0
points
Most recent by
Robert Nunes
July 2019
Getting Started & Troubleshooting
PLA Ultimaker Cura settings
390
views
2
comments
0
points
Most recent by
Laser8302
July 2019
Getting Started & Troubleshooting
Lubricating the sliding rods
107
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
Layer Shift (SOLVED)
1.1K
views
9
comments
0
points
Most recent by
keithirma
August 2019
Getting Started & Troubleshooting
I think my A5S extruder is clogged
110
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
Printing with USB cable
213
views
1
comment
0
points
Most recent by
Samuel Pinches
July 2019
Getting Started & Troubleshooting
Next