Home JGAurora A5 & A3S Getting Started & Troubleshooting

Stepper Driver: Y driver error detected

HevilpHevilp Posts: 136🌟 Super Member 🌟
Hi,

today I got the error below, but there is no good information:
Some1 got it too?
> 23:00:36.415: Y driver error detected:
> 23:00:36.418:   X Y E0
> 23:00:36.418: Enabled  true true true
> 23:00:36.419: Set current 800 800 500
> 23:00:36.422: RMS current 795 795 489
> 23:00:36.423: MAX current 1121 1121 689
> 23:00:36.425: Run current 25/31 25/31 15/31
> 23:00:36.426: Hold current 12/31 12/31 7/31
> 23:00:36.426: CS actual  25/31 25/31 15/31
> 23:00:36.429: PWM scale 53 82 29
> 23:00:36.430: vsense  1=.18 1=.18 1=.18
> 23:00:36.432: stealthChop true true true
> 23:00:36.432: msteps  16 16 16
> 23:00:36.433: tstep  265 2110 1617
> 23:00:36.433: pwm
> 23:00:36.436: threshold  98 98 95
> 23:00:36.436: [mm/s]  100.85 100.85 30.04
> 23:00:36.437: OT prewarn false false false
> 23:00:36.438: OT prewarn has
> 23:00:36.440: been triggered false false false
> 23:00:36.440: off time  5 5 5
> 23:00:36.441: blank time 24 24 24
> 23:00:36.441: hysterisis
> 23:00:36.442: -end  2 2 2
> 23:00:36.443: -start  3 3 3
> 23:00:36.444: Stallguard thrs 0 0 0
> 23:00:36.444: DRVSTATUS X Y E0
> 23:00:36.445: stallguard    
> 23:00:36.445: sg_result  0 0 0
> 23:00:36.448: fsactive    
> 23:00:36.448: stst    
> 23:00:36.448: olb    
> 23:00:36.449: ola    
> 23:00:36.449: s2gb    
> 23:00:36.449: s2ga    
> 23:00:36.450: otpw    
> 23:00:36.451: ot    
> 23:00:36.451: Driver registers:
> 23:00:36.452:  X = 0x00:19:00:00
> 23:00:36.452:  Y = 0x00:19:00:00
> 23:00:36.453:  E0 = 0x00:0F:00:00
Post edited by Hevilp on

Comments

  • DaHaiDaHai Posts: 36🌟 Super Member 🌟
    Is this with TMC2130 drivers?
    On the X Y and E0?
    If so, first thing to try is raising the  current on the Y to 1000 - its  a big bed to move around.
  • HevilpHevilp Posts: 136🌟 Super Member 🌟
    edited June 2018
    I probably figured out that it is a Marlin issue. I made an A5 Marlin 2.x.x. Fw with tmc2130 yesterday and it is working nice, over 25 hours. (the 1.1.8 ran man Times >30 hours too.

    Tomorrow I will post a File here with the default non tmc2130 version for the community. 

    It seems there is a problem with the driver, It reports errors to Marlin where are no errors, 1 hint is to put a 10k pulldown on miso line. 

    I hope the Marlin v2 will cure it, I will inform you. 

    Target is to get the dual extruder working. 

    Post edited by Hevilp on
Sign In or Register to comment.