Home‚Äļ JGAurora A5 & A3S‚Äļ Modifications & Upgrades

TMC 2130 SPI

hugoczhugocz Posts: 17Member
edited May 2018 in Modifications & Upgrades
My printer doesnt home since i've made the change to the TMC2130, i get the messages that im leaving below and only moves the z and the x, if i touch to move y it moves z.

"Y driver error detected:
short to ground (coil B)
        X    Y
Enabled        true    true
Set current    800    800
RMS current    795    795
MAX current    1121    1121
Run current    25/31    25/31
Hold current    12/31    12/31
CS actual        12/31    25/31
PWM scale    19    0
vsense        1=.18    1=.18
stealthChop    true    true
msteps        16    16
tstep        1048575    124
pwm
threshold        98    98
[mm/s]        100.85    100.85
OT prewarn    false    false
OT prewarn has
been triggered    false    false
off time        5    5
blank time    24    24
hysterisis
-end        2    2
-start        3    3
Stallguard thrs    0    0
DRVSTATUS    X    Y
stallguard
sg_result        0    0
fsactive
stst        X
olb
ola            X
s2gb            X
s2ga
otpw
ot
Driver registers:
    X = 0x80:0C:00:00
    Y = 0x30:19:00:00
Error:Printer halted. kill() called!
[ERROR] Error:Printer halted. kill() called!
"
"echo:endstops hit:  Z:1.00
echo:endstops hit:  X:64.97
echo:endstops hit:  X:64.95
echo:endstops hit:  X:64.93
echo:endstops hit:  X:64.90
echo:endstops hit:  X:64.87
echo:endstops hit:  X:64.85
echo:endstops hit:  X:64.83
Y driver error detected:
short to ground (coil B)
        X    Y
Enabled        true    true
Set current    800    800
RMS current    795    795
MAX current    1121    1121
Run current    25/31    25/31
Hold current    12/31    12/31
CS actual        25/31    25/31
PWM scale    62    0
vsense        1=.18    1=.18
stealthChop    true    true
msteps        16    16
tstep        1048575    124
pwm
threshold        98    98
[mm/s]        100.85    100.85
OT prewarn    false    false
OT prewarn has
been triggered    false    false
off time        5    5
blank time    24    24
hysterisis
-end        2    2
-start        3    3
Stallguard thrs    0    0
DRVSTATUS    X    Y
stallguard
sg_result        0    0
fsactive
stst        X
olb        X
ola            X
s2gb            X
s2ga
otpw
ot
Driver registers:
    X = 0xC0:19:00:00
    Y = 0x30:19:00:00
Error:Printer halted. kill() called!
[ERROR] Error:Printer halted. kill() called!"


Post edited by hugocz on

Comments

  • HevilpHevilp Posts: 136ūüĆü Super Member ūüĆü
    It seems that there wire of the stepper driver are not good, have you checked?
  • hugoczhugocz Posts: 17Member
    yes i've changed all the cables, i bought 1 pin dupont cables just to be sure
Sign In or Register to comment.