Toggle navigation
Categories
Discussions
Activity
🔨Firmware
🧰Starter Kit
💡Wiki
🛒Shop
Sign In
Home
Please note: the forum is closed.
No new user registrations are accepted. For more info, please click here.
Back to Profile
AETEK
About
Username
AETEK
Joined
June 2018
Visits
286
Last Active
March 2020
Roles
🌟 Super Member 🌟
Location
Germany
Thanked
34
Posts
106
Activity
Thanked
34
Discussions
28
Comments
78
<div>Hi,</div><div>yes it works and some more addons, too.</div><div>Actually I am busy with optimizing my other 3D printer. So no A5 topic.</div><div>
&…
Thanked by
1
darthmolen
<div> <i><b>>>If you were an MKS engineer, would you suggest that they should use a
smaller value resistor, to produce a more powerful pull up?<<</b></i>…
Thanked by
1
Samuel Pinches
<span>Hi Guys,
I have just developed a hardware upgrade for the A5 and am in the test phase. In the process of development, I came across some unexpected problems with the MKS TFT28 filamen…
Thanked by
2
Werewolf
Samuel Pinches
Yes, sound is back again. :)
Thanked by
1
Samuel Pinches
<div>Hello,</div><div>Samuel wanted to watch a video, after the conversions to reduce the noise of my A5. Here it is.</div>
<div><span>For playing the video yo…
Thanked by
1
Samuel Pinches
<span>Hello,
So my pretty new A5 has a sensitive coating that is attacked by pure alcohol. Look here:</span><div><a href="https://jgmakerforum.com/discussion/comment/779/#Com…
Thanked by
1
Samuel Pinches
<div><span>Hello,
yes, there is a standard. Otherwise you would not know how to mount the plug to the ribbon cable. Therefore, the plug has the triangular mark. MKS did it right with …
Thanked by
1
Samuel Pinches
<span><span>Hello,
</span>Unfortunately there are again errors in the documentation for the MKS GEN_L 1.0 motherboard. I can not say if there are more errors because I have not …
Thanked by
1
Samuel Pinches
<span><span>Hello,
</span>Cleaning the nozzle is important. The filament remaining in the hot end tends to denature when it is not moved. This leads to problems in printing qual…
Thanked by
1
Samuel Pinches
<span>Hello,
After your error description, I would guess that a limit switch does not work. The collision and further stress could have overloaded a stepper driver. I
assume that you h…
Thanked by
1
Jari Christopherson
<span>Hello,
I have found remnants of 0.5mm printed circuit board copper coated.
Then I etched the copper away and mounted the PCB material down between the clamp and the heated bed. Th…
Thanked by
1
Samuel Pinches
<div><div><div><div></div></div></div></div><div></div><div><div></div></div><span><span>Hello,
<…
Thanked by
2
Samuel Pinches
seafian
<span>Hello,
thanks for the hint. The links are working now.
The board is part of the project, which I describe in my first post.
The project is not finished yet. I'll show some con…
Thanked by
1
sanjibukai
<div>Hello from Germany,</div><div></div><span>at the A5 there are in my opinion still things that are in need of improvement. Currently I am working on a new interface …
Thanked by
1
sanjibukai
<span>Hello,
thanks for the links to the two videos. Especially the second video answers my question. The processor is not an Arduino, but an ATMEGA2560. This is a RISC processor that is ve…
Thanked by
1
Samuel Pinches
<span>
<a href="https://jgaurorawiki.com/a5/make-the-a5-quieter">https://jgaurorawiki.com/a5/make-the-a5-quieter</a>
Hello,
my article series about the possibili…
Thanked by
2
Samuel Pinches
seafian
<span>Hello,
I have again created three new articles in the WIKI, which concern the subject noise reduction of the A5.
</span><div>This time it's about the little fans who l…
Thanked by
1
Samuel Pinches
<div><i>>></i>
<span><i>If I understand your circuit right, it's just about pressing the power
switch as long as the A5 takes control on the solid state r…
Thanked by
1
seafian
<span>Hello,
you may not have seen: <b>classification professional.</b>
</span><div><span>I have indicated a degree of difficulty in all my projects.
&…
Thanked by
1
Samuel Pinches
<span>Hello,
</span><div><span>I've just released a new project for the A5 in the wiki:
</span></div><div><a href="https://jgaurorawiki.com/a5/pr…
Thanked by
2
Samuel Pinches
seafian
<span>Hello,
</span><div><span>After spending hours setting up a new feature on the MKS TFT2.8 display, I did some research.
</span></div><div><s…
Thanked by
1
Samuel Pinches
Fine, I have a ton of other extensions to add to the wiki, coming soon.
Thanked by
1
Samuel Pinches
<div>Update:</div><div>The pinout designations of the MKS-GEN_L 1.0 documentation are partly faulty: </div><div><span><a href="https://jgmakerforum.com/discussi…
Thanked by
1
Samuel Pinches
<span>Hello,
</span><div><span>The pinout designations of the MKS-GEN_L 1.0 documentation are partly faulty.
</span></div><div><span>I've been…
Thanked by
1
Samuel Pinches
<span>Hello,
</span><div>I have heard several times that the MKS GEN-L mainboard has problems with the inputs of the temperature sensors in combination with the A5. I am develop…
Thanked by
1
Samuel Pinches
<span>Hello,
</span><div><span>Recently I bought three 1kG spools of PLA filament from Ebay via a Chinese seller with a warehouse in Germany.
</span></div>…
Thanked by
2
Milk_And_Ammo
Samuel Pinches
<span><span>Hello,
</span>a few days ago I got my A5. The Z-axis
couplers were bent and the plug of the filament-out sensor had no
contact, although correctly plugged …
Thanked by
3
GEOIV
beata
Samuel Pinches