Home› JGAurora A5 & A3S› Getting Started & Troubleshooting
Please note: the forum is closed.
No new user registrations are accepted. For more info, please click here.

Heating problem Bed and Extruder

hugoczhugocz Posts: 17Member
edited April 2019 in Getting Started & Troubleshooting
I was adding 2 mosfet to my jgaurora a5, after adding all the cables the printer was not warming up neither on the bed or the extruder, after that i brought everything to the original form but still getting no heating in both places.
Anyone had that problem or know where that problem could come from?
Post edited by hugocz on

Comments

  • Der_MuckDer_Muck Posts: 265🌟 Super Member 🌟
    Without pictures its a probem to tell you anything, we dont see how you did the job. Normaly it should work without a problem.
  • Samuel PinchesSamuel Pinches Posts: 2,997Administrator
    @hugocz

    Can you give us more details on how you added the mosfets? Using the original mosfets to turn on the additional mosfets?

    You need to test this while plugged into a computer and connected with pronterface. That way you will see if there are any heating errors.

    https://jgaurorawiki.com/pronterface
  • hugoczhugocz Posts: 17Member
    Sorry for not aswering before work didnt let me, now its back to where it was as you can see in the picture
    i gonna let sketch how i wanted to connect the 2 mosfets, and im leaving what says in the pronterface

    Connecting...<br>start<br>Printer is now online.<br>echo:Marlin 1.1.8<br>echo: Last Updated: 2017-12-25 12:00 | Author: (Telli Mantelli, Kris Waclawski, Samuel Pinches & Michael Gilardi, 21 Jan 2018)<br>echo:Compiled: Apr  8 2019<br>echo: Free Memory: 2696  PlannerBufferBytes: 1264<br>echo:V47 stored settings retrieved (614 bytes; crc 60999)<br>echo:  G21    ; Units in mm<br>echo:  M149 C ; Units in Celsius<br>echo:Filament settings: Disabled<br>echo:  M200 D1.75<br>echo:  M200 D0<br>echo:Steps per unit:<br>echo:  M92 X80.00 Y80.00 Z800.00 E100.00<br>echo:Maximum feedrates (units/s):<br>echo:  M203 X500.00 Y500.00 Z15.00 E25.00<br>echo:Maximum Acceleration (units/s2):<br>echo:  M201 X1000 Y500 Z100 E5000<br>echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel><br>echo:  M204 P800.00 R800.00 T1000.00<br>echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk><br>echo:  M205 S0.00 T0.00 B20000 X8.00 Y3.00 Z0.30 E5.00<br>echo:Home offset:<br>echo:  M206 X0.00 Y0.00 Z0.00<br>echo:Auto Bed Leveling:<br>echo:  M420 S0 Z0.00<br>echo:Material heatup parameters:<br>echo:  M145 S0 H205 B70 F255<br>echo:  M145 S1 H240 B110 F0<br>echo:PID settings:<br>echo:  M301 P35.30 I4.35 D71.57<br>echo:Z-Probe Offset (mm):<br>echo:  M851 Z4.10<br>echo:Stepper driver current:<br>echo:  M906 X 800 Y 800 Z 0 E0 0<br>Y driver error detected:<br>overtemperature<br>short to ground (coil A)<br>short to ground (coil B)<br>		X	Y	Z	E0<br>Enabled		false	false	false	false<br>Set current	800	800	0	0<br>RMS current	795	795	1767	1767<br>MAX current	1121	1121	2491	2491<br>Run current	25/31	25/31	31/31	31/31<br>Hold current	12/31	12/31	31/31	31/31<br>CS actual		12/31	31/31	31/31	31/31<br>PWM scale	1	255	1	1<br>vsense		1=.18	1=.18	0=.325	0=.325<br>stealthChop	true	true	true	true<br>msteps		16	0	16	16<br>tstep		1048575	4294967295	1048575	1048575<br>pwm<br>threshold		0	0	0	0<br>[mm/s]		-	-	-	-<br>OT prewarn	false	true	false	false<br>OT prewarn has<br>been triggered	false	false	false	false<br>off time		5	15	5	5<br>blank time	24	54	24	24<br>hysterisis<br>-end		2	12	2	2<br>-start		3	8	3	3<br>Stallguard thrs	0	0	0	0<br>DRVSTATUS	X	Y	Z	E0<br>stallguard			X<br>sg_result		0	1023	0	0<br>fsactive			X<br>stst		X	X	X	X<br>olb			X<br>ola			X<br>s2gb			X<br>s2ga			X<br>otpw			X<br>ot			X<br>Driver registers:<br>	X = 0x80:0C:00:00<br>	Y = 0xFF:FF:FF:FF<br>	Z = 0x80:1F:00:00<br>	E0 = 0x80:1F:00:00<br>Error:Printer halted. kill() called!<br>[ERROR] Error:Printer halted. kill() called!<br><br>




  • Der_MuckDer_Muck Posts: 265🌟 Super Member 🌟
    There is the problem written in the PF log.
    Check your Y motor, you may have a problem with the wireing
    Y driver error detected:<br>overtemperature<br>short to ground (coil A)<br>short to ground (coil B<span>)</span>
    Thanked by 1hugocz
  • hugoczhugocz Posts: 17Member
    edited April 2019
    There is the problem written in the PF log.
    Check your Y motor, you may have a problem with the wireing
    Y driver error detected:<br>overtemperature<br>short to ground (coil A)<br>short to ground (coil B)


    This problem is resolved some kind of bad contact on the steppers or the cables, but still on the monitor of the printer doesn't show the temp changing , i changed it  in pronterface and the temps are rising, but when i disconnect and use the monitor it doesn't change (appears 0/0 you can increment)

    One more thing is the way i was mounting the mosfets the correct way?

    Post edited by hugocz on
Sign In or Register to comment.