Please note: the forum is closed.
No new user registrations are accepted. For more info, please click here.
No new user registrations are accepted. For more info, please click here.
best encloser I can think of for JGAURORA A5 that uses the printer frame to hold it :)
coolt5
Posts: 38🌟 Super Member 🌟
before this i was printing abs all the time with no problem at all using my old fashion way LoooooooooL
with some easy to use technology . light from the hole in top left and web cam to call skype any time and see the printing process.
https://youtu.be/vll6gw1t8QA
so i decide to upgrade my encloser so working time.
i made this by taking the right length and cut the Acrylic and glow them together and made some 3d part to hold them in place .
here are some pictures . and i would like to know your Opinion about it.
print this to hold the front box and fix it to the frame with screws and nuts
tow for both sides
after glowing the Acrylic i make tow hole in the top for securing the box and easy to use (install and remove the box by hands only just left it up and go)
after i made the door in front i notice its weak from the lower (below the door)
so i made tow part to Strengthen it in the corners
as you can see it seals the gaps between the frame and box
you dont need to go all the way down because i need a cold air for my mean board and stepper drivers TMC2130 and power supply
i prints this small sticks to insert it on top of acrylic to secure the box
i still need to close all the holes in the sides with tapes
i find the door hinges in thingiverse and its works for me
the other side will need some modification because i need to move the filament holder and extruder motor a few milemeters to the left.
will post hear when done.
pls feel free to let me know what you think and any Suggestion.
thanks
SAM
with some easy to use technology . light from the hole in top left and web cam to call skype any time and see the printing process.
https://youtu.be/vll6gw1t8QA
so i decide to upgrade my encloser so working time.
i made this by taking the right length and cut the Acrylic and glow them together and made some 3d part to hold them in place .
here are some pictures . and i would like to know your Opinion about it.
print this to hold the front box and fix it to the frame with screws and nuts
tow for both sides
after glowing the Acrylic i make tow hole in the top for securing the box and easy to use (install and remove the box by hands only just left it up and go)
after i made the door in front i notice its weak from the lower (below the door)
so i made tow part to Strengthen it in the corners
as you can see it seals the gaps between the frame and box
you dont need to go all the way down because i need a cold air for my mean board and stepper drivers TMC2130 and power supply
i prints this small sticks to insert it on top of acrylic to secure the box
i still need to close all the holes in the sides with tapes
i find the door hinges in thingiverse and its works for me
the other side will need some modification because i need to move the filament holder and extruder motor a few milemeters to the left.
will post hear when done.
pls feel free to let me know what you think and any Suggestion.
thanks
SAM
Thanked by 1Samuel Pinches
Post edited by coolt5 on
Comments
Also close the enclose on the down side. Without it the hot air will go up and away and get more cold air from down. So its getting very windy, like on a fireplace.
Thats my A5 for you to see what i mean:
can post more pics from all sides
Howdy, Stranger!
RegisterIt looks like you've been lurking for a while.
If you register, we will remember what you have read and notify you about new comments. You will also be able to participate in discussions.
So if you'd like to get involved, register for an account, it'll only take you a minute!