Please note: the forum is closed.
No new user registrations are accepted. For more info, please click here.
No new user registrations are accepted. For more info, please click here.
Stepper Driver: Y driver error detected
Hevilp
Posts: 136🌟 Super Member 🌟
Hi,
today I got the error below, but there is no good information:
Some1 got it too?
> 23:00:36.415: Y driver error detected:
today I got the error below, but there is no good information:
Some1 got it too?
> 23:00:36.415: Y driver error detected:
> 23:00:36.418: X Y E0
> 23:00:36.418: Enabled true true true
> 23:00:36.419: Set current 800 800 500
> 23:00:36.422: RMS current 795 795 489
> 23:00:36.423: MAX current 1121 1121 689
> 23:00:36.425: Run current 25/31 25/31 15/31
> 23:00:36.426: Hold current 12/31 12/31 7/31
> 23:00:36.426: CS actual 25/31 25/31 15/31
> 23:00:36.429: PWM scale 53 82 29
> 23:00:36.430: vsense 1=.18 1=.18 1=.18
> 23:00:36.432: stealthChop true true true
> 23:00:36.432: msteps 16 16 16
> 23:00:36.433: tstep 265 2110 1617
> 23:00:36.433: pwm
> 23:00:36.436: threshold 98 98 95
> 23:00:36.436: [mm/s] 100.85 100.85 30.04
> 23:00:36.437: OT prewarn false false false
> 23:00:36.438: OT prewarn has
> 23:00:36.440: been triggered false false false
> 23:00:36.440: off time 5 5 5
> 23:00:36.441: blank time 24 24 24
> 23:00:36.441: hysterisis
> 23:00:36.442: -end 2 2 2
> 23:00:36.443: -start 3 3 3
> 23:00:36.444: Stallguard thrs 0 0 0
> 23:00:36.444: DRVSTATUS X Y E0
> 23:00:36.445: stallguard
> 23:00:36.445: sg_result 0 0 0
> 23:00:36.448: fsactive
> 23:00:36.448: stst
> 23:00:36.448: olb
> 23:00:36.449: ola
> 23:00:36.449: s2gb
> 23:00:36.449: s2ga
> 23:00:36.450: otpw
> 23:00:36.451: ot
> 23:00:36.451: Driver registers:
> 23:00:36.452: X = 0x00:19:00:00
> 23:00:36.452: Y = 0x00:19:00:00
> 23:00:36.453: E0 = 0x00:0F:00:00
Post edited by Hevilp on
Comments
On the X Y and E0?
If so, first thing to try is raising the current on the Y to 1000 - its a big bed to move around.
Tomorrow I will post a File here with the default non tmc2130 version for the community.
It seems there is a problem with the driver, It reports errors to Marlin where are no errors, 1 hint is to put a 10k pulldown on miso line.
I hope the Marlin v2 will cure it, I will inform you.
Target is to get the dual extruder working.
Howdy, Stranger!
RegisterIt looks like you've been lurking for a while.
If you register, we will remember what you have read and notify you about new comments. You will also be able to participate in discussions.
So if you'd like to get involved, register for an account, it'll only take you a minute!