Getting Started & Troubleshooting

Discussion List

• controls not working

  26 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• leveling does not go to all four corners, stops in about 4" square, is it LCD program?

  37 views 2 comments 0 points Most recent by Samuel Pinches July 2019
• Auto Bed level - noise on Y Axis movement

  93 views 3 comments 0 points Most recent by Der_Muck June 2019
• Printing a Cube VS. Printing a Cylinder

  66 views 2 comments 0 points Most recent by JayJoe June 2019
• Octolapse settings

  254 views 2 comments 0 points Most recent by Richy_T June 2019
• A5S filament motor clicking only at beginning of print

  162 views 4 comments 0 points Most recent by mgrabow June 2019
• Importing cura printer profiles for miniatures for A5s

  174 views 0 comments 0 points Started by KurtMax June 2019
• Printer not stopping heating

  113 views 4 comments 0 points Most recent by Jacob_Vaughan June 2019
• Why does filament sometimes get clogged in the hot-end?

  776 views 4 comments 0 points Most recent by ThingsNSchtuff June 2019
• Printer stopped after retract

  104 views 19 comments 0 points Most recent by Samuel Pinches June 2019
• Pause at z layer

  881 views 10 comments 0 points Most recent by Der_Muck May 2019
• closing machine error

  362 views 1 comment 0 points Most recent by Samuel Pinches May 2019
• A5 heatbed stop heat up problem

  2.9K views 17 comments 0 points Most recent by caligarius May 2019
• Bought dial gauge but all the mounts are shit, any help?

  58 views 1 comment 0 points Most recent by cs2000 May 2019
• Cura Extra Prime Amount

  80 views 0 comments 0 points Started by JetBoyTR May 2019
• Z axis steppers grinding noise TMC2130

  1.2K views 16 comments 0 points Most recent by cs2000 May 2019
• Printer Continuing to print after cooling down?

  47 views 3 comments 0 points Most recent by Der_Muck May 2019
• Replacement filament guide (bearing?)

  145 views 13 comments 0 points Most recent by Der_Muck May 2019
• Extruder thermistor problem

  469 views 23 comments 0 points Most recent by Der_Muck May 2019
• A3 anti-interference cable

  72 views 2 comments 0 points Most recent by mufasa48 May 2019
• SOLVED: MINTEMP triggered, system stopped! Heater_ID: 0 (Printer randomly stopping mid print)

  1.8K views 1 comment 0 points Most recent by Samuel Pinches May 2019
• How do I replace the threaded filament tube that holds the print head?

  533 views 16 comments 0 points Most recent by Sparks May 2019
• Best way to clean pla off extruder

  530 views 8 comments 0 points Most recent by beata April 2019
• Strange knocking sound from extruder carriage when printing

  203 views 3 comments 0 points Most recent by Samuel Pinches April 2019
• Mark On Top Surface

  62 views 1 comment 0 points Most recent by Laser8302 April 2019
• PETG printing = a lot of frustrations

  686 views 9 comments 0 points Most recent by Laser8302 April 2019
• Carbon fiber filament

  695 views 19 comments 0 points Most recent by cs2000 April 2019
• Heating problem Bed and Extruder

  146 views 5 comments 0 points Most recent by hugocz April 2019
• Bad Prints

  220 views 8 comments 0 points Most recent by Der_Muck April 2019
• screen not working

  629 views 4 comments 0 points Most recent by Samuel Pinches April 2019