Getting Started & Troubleshooting

Discussion List

• INACCURATE TEMPERATURE

  65 views 2 comments 0 points Most recent by Stephen Todd February 2020
• Settings and Configurations

  9K views 8 comments 0 points Most recent by Daniel Marc Ehrhardt February 2020
• LCD Display Registering repeated presses when not being touched

  159 views 6 comments 0 points Most recent by ahoy February 2020
• Spare Parts A5

  88 views 3 comments 0 points Most recent by Stephen Todd February 2020
• (JGAurora A5s) - Display died during Print?

  78 views 1 comment 0 points Most recent by Stephen Todd February 2020
• JGaurora a5 Small screws

  194 views 3 comments 0 points Most recent by Eye January 2020
• temp issue

  84 views 3 comments 0 points Most recent by Stephen Todd January 2020
• temp troubles led to bigger problems

  94 views 1 comment 0 points Most recent by Samuel Pinches December 2019
• A5 Y-axis problem after reassembly

  848 views 11 comments 0 points Most recent by slppugsy December 2019
• TPU prints falling apart :(

  411 views 4 comments 0 points Most recent by Samuel Pinches December 2019
• Hello everyone. I have a question about file compliance

  98 views 3 comments 0 points Most recent by Laser8302 December 2019
• A3S (version 1), prints sticking to bed.

  42 views 1 comment 0 points Most recent by Samuel Pinches December 2019
• salve, la mia stampante dopo un determinato tempo si blocca

  54 views 1 comment 0 points Most recent by Laser8302 December 2019
• Did anyone tried to print this?

  67 views 1 comment 0 points Most recent by Laser8302 December 2019
• Print is weird and won't stick to the bed

  210 views 3 comments 0 points Most recent by Laser8302 December 2019
• Clip being hit by start script when wiping

  38 views 3 comments 0 points Most recent by Samuel Pinches December 2019
• No Files Found

  608 views 11 comments 0 points Most recent by Winter December 2019
• min temp reached error

  694 views 8 comments 0 points Most recent by Samuel Pinches November 2019
• A3S V1 Air Prints from Z at Which Temperature is Set, Unless G28 (Home Extruder) is Added Manually

  55 views 2 comments 0 points Most recent by Samuel Pinches November 2019
• A3S V1 - Must Tighten Screw for Leveling Position 1 to the Maximum Amount, and Z Degreasing

  52 views 1 comment 0 points Most recent by poikilos November 2019
• LCD/Z-axis problems

  82 views 1 comment 0 points Most recent by Samuel Pinches November 2019
• Please help!!! After each print goes to corner and extrude

  137 views 1 comment 0 points Most recent by Samuel Pinches October 2019
• Starting heat settings

  116 views 8 comments 0 points Most recent by rhaub101 October 2019
• Firmware update for A5 Mainboard and LCD controller display issues.

  125 views 2 comments 0 points Most recent by Samuel Pinches October 2019
• Temperature issue

  207 views 4 comments 0 points Most recent by Matt October 2019
• home issue?

  39 views 0 comments 0 points Started by Matt October 2019
• Temp. not correct when plugging in to PC

  40 views 7 comments 0 points Most recent by g_pwn October 2019
• JgAurora A5 Magic number

  1.1K views 10 comments 0 points Most recent by cmarabate October 2019
• Please Diagnose my issue

  72 views 2 comments 0 points Most recent by Marian Würker September 2019
• Blank white screen, but printer working otherwise

  798 views 5 comments 0 points Most recent by qthurtle September 2019