Getting Started & Troubleshooting

Discussion List

• Loud Beeping from A3S. Print halted

  551 views 1 comment 0 points Most recent by Samuel Pinches April 2019
• Part cooling fan not turning ON with Cura 4.0?

  546 views 7 comments 0 points Most recent by chilman408 March 2019
• psu fan, start when hot

  54 views 2 comments 0 points Most recent by Samuel Pinches March 2019
• User Manual Support Guide for JGAurora A5

  793 views 0 comments 0 points Started by Samuel Pinches March 2019
• Noob question and did I just damage my heatbed?

  245 views 6 comments 0 points Most recent by Samuel Pinches March 2019
• WTF!!!

  80 views 1 comment 0 points Most recent by Samuel Pinches March 2019
• Bed heater stopped working

  225 views 20 comments 0 points Most recent by Der_Muck March 2019
• Feet broke off, also firmware flashing.

  62 views 16 comments 0 points Most recent by cs2000 March 2019
• Missing configuration file

  275 views 12 comments 0 points Most recent by cs2000 March 2019
• Baby stepping save?

  74 views 1 comment 0 points Most recent by Samuel Pinches March 2019
• A5 randomly crashes with the message "closing mashine ...."

  312 views 10 comments 0 points Most recent by Samuel Pinches March 2019
• X-axis error: became unidirectional

  141 views 11 comments 0 points Most recent by sasa March 2019
• change filament gcode script

  611 views 12 comments 0 points Most recent by hanzfranz March 2019
• Fan not working.

  595 views 23 comments 0 points Most recent by XeS0r March 2019
• Offset printout to the right

  71 views 1 comment 0 points Most recent by Der_Muck March 2019
• Kasey

  50 views 1 comment 0 points Most recent by Samuel Pinches March 2019
• IR Sensor does not work

  230 views 10 comments 0 points Most recent by Samuel Pinches March 2019
• Run Out Sensor (How to Actually use It)

  309 views 4 comments 0 points Most recent by cs2000 March 2019
• Print suddenly stops with no sond nor message (A3-S)

  269 views 9 comments 0 points Most recent by Samuel Pinches March 2019
• Tuning stock stepper drivers

  48 views 2 comments 0 points Most recent by rhaub101 March 2019
• Grinding the bed with BLTouch

  241 views 6 comments 0 points Most recent by FreddyGaertner March 2019
• TMC 2208 snipped pin issue

  85 views 2 comments 0 points Most recent by itisnot_me March 2019
• Z Axis Homing Issue (Too Low)

  698 views 5 comments 0 points Most recent by Samuel Pinches February 2019
• Heater Bed Cable 4 Pin Connector

  166 views 4 comments 0 points Most recent by Samuel Pinches February 2019
• Problem With Stringing Inside The Shell

  62 views 5 comments 0 points Most recent by Samuel Pinches February 2019
• Overheat

  51 views 1 comment 0 points Most recent by Samuel Pinches February 2019
• Problems to level the bed.

  107 views 2 comments 0 points Most recent by Der_Muck February 2019
• Problem with jgaurora a5

  100 views 1 comment 0 points Most recent by Der_Muck February 2019
• A5 stops printing SOLVED

  357 views 4 comments 0 points Most recent by Der_Muck February 2019
• Filament feed in length

  141 views 3 comments 0 points Most recent by Der_Muck February 2019