Getting Started & Troubleshooting

Discussion List

• Fozu gcode profile

  43 views 1 comment 0 points Most recent by michalko99 December 2020
• A5 z axis blockage

  47 views 2 comments 0 points Most recent by Laser8302 November 2020
• A5 extruder block

  57 views 2 comments 0 points Most recent by Samuel Pinches November 2020
• A5 heat block shaft

  60 views 3 comments 0 points Most recent by Samuel Pinches November 2020
• Z-Axis Level Problem

  199 views 3 comments 0 points Most recent by Zemarus November 2020
• Error WinTemp triggered system stopped -Heater_id : 0

  151 views 4 comments 0 points Most recent by Laser8302 October 2020
• Print doesn't start

  60 views 5 comments 0 points Most recent by Barts October 2020
• 25mm layer shift !

  69 views 1 comment 0 points Most recent by michalko99 October 2020
• How to disassemble print head/gantry (A5)?

  275 views 4 comments 0 points Most recent by Laser8302 October 2020
• Print starting Problems

  70 views 2 comments 0 points Most recent by Laser8302 October 2020
• A3S bed not moving and not heating

  46 views 2 comments 0 points Most recent by michalko99 September 2020
• New parts for JGAurora A5

  115 views 1 comment 0 points Most recent by Samuel Pinches September 2020
• A5 - no movement X Y Z, except while pressing home

  37 views 4 comments 0 points Most recent by Samuel Pinches September 2020
• Not extruding in prints sliced with Cura, manual extrusion works

  129 views 2 comments 0 points Most recent by shukuyen August 2020
• Desesperado con las placas... UN FIRMWARE POR FAVOR

  405 views 2 comments 0 points Most recent by Alejo August 2020
• were to get a Z axis Switch For the JG aurora a5?

  30 views 1 comment 0 points Most recent by Eye August 2020
• A5 :: Bed Heating Problem

  148 views 5 comments 0 points Most recent by Samuel Pinches July 2020
• After Flashing Marlin 1.1.8 A5 Extruder stops at 120mm, Printer keeps going

  58 views 3 comments 0 points Most recent by Samuel Pinches July 2020
• A5 z-axis very loud and slow all of a sudden

  475 views 8 comments 0 points Most recent by Jaltizer July 2020
• adhesion

  49 views 2 comments 0 points Most recent by Laser8302 July 2020
• Printer keeps pausing for no reason...

  191 views 3 comments 0 points Most recent by Laser8302 July 2020
• JGAurora A5 Bowden Coupler - Spare Part Link to German Seller

  58 views 1 comment 0 points Most recent by Samuel Pinches June 2020
• Fan duct melt...

  199 views 4 comments 0 points Most recent by delirii June 2020
• Skewed / Leaning Prints

  232 views 3 comments 0 points Most recent by Samuel Pinches June 2020
• A5 Hot end cooling fan not working

  75 views 4 comments 0 points Most recent by Laser8302 June 2020
• A5 Problem

  114 views 6 comments 0 points Most recent by Laser8302 June 2020
• my jgaurora a5 not powering up

  132 views 4 comments 0 points Most recent by Laser8302 June 2020
• Bed and extruder not heating

  217 views 4 comments 0 points Most recent by Laser8302 June 2020
• Firmware

  137 views 2 comments 0 points Most recent by bhjt1728 May 2020
• Updated Marlin Firmware not working

  451 views 6 comments 0 points Most recent by mackpeed May 2020