Getting Started & Troubleshooting

Discussion List

• NEW A5S Official Firmware - April 25th 2019

  Announcement 1.2K views 8 comments 0 points Most recent by Samuel Pinches September 2020
• Y Layer Shifting - Only on some prints

  16 views 9 comments 0 points Most recent by michalko99 May 31
• Touch Screen Fault

  9 views 1 comment 0 points Most recent by Samuel Pinches May 25
• Enable Mesh Bed Leveling

  9 views 3 comments 0 points Most recent by Samuel Pinches May 25
• My LCD has stopped working

  20 views 1 comment 0 points Most recent by Samuel Pinches May 23
• Printer resets Upon bed Heating

  15 views 4 comments 0 points Most recent by Samuel Pinches May 21
• Pronterface

  33 views 1 comment 0 points Most recent by Samuel Pinches May 21
• Scratched Heater Bed from underneath

  19 views 1 comment 0 points Most recent by Samuel Pinches May 2
• jgaurora a5s lcd

  43 views 4 comments 0 points Most recent by Samuel Pinches April 21
• EXTU 1 SENSOR ERROR AND HEAT BED NOT HEATING

  22 views 6 comments 0 points Most recent by Nivas April 8
• A5S Adhesion issue - Can't figure out what is wrong [SOLVED]

  54 views 4 comments 0 points Most recent by Samuel Pinches March 29
• replacement A5S motherboard

  38 views 3 comments 0 points Most recent by Samuel Pinches March 23
• Hey guys.. I had an issue last night at 99% print after 8 hrs of printing.. PLEASE HELP!

  22 views 3 comments 0 points Most recent by Samuel Pinches March 21
• Having problems compiling a5s color ui firmware on Arduino

  72 views 11 comments 0 points Most recent by BeauArmstrong March 15
• A5S LCD powers on with USB connection

  18 views 2 comments 0 points Most recent by GEOIV March 11
• A5s and PETG

  111 views 4 comments 0 points Most recent by Eye February 28
• A5S stripped screw help

  37 views 6 comments 0 points Most recent by pdb6251 February 27
• LCD display doesn't turn on

  50 views 2 comments 0 points Most recent by pdb6251 February 27
• Motherboard burned out

  38 views 2 comments 0 points Most recent by Samuel Pinches February 22
• If I use Bedleveling the slicer tell me the need up to 4 times of time

  60 views 5 comments 0 points Most recent by Samuel Pinches February 14
• X-Axis Noise and LCD Screen Black

  31 views 3 comments 0 points Most recent by Just_Jo February 11
• A5S smoking after fans shorted: Help!

  56 views 6 comments 0 points Most recent by michalko99 February 11
• A5S Err. MAXTEMP: BED help..

  53 views 10 comments 0 points Most recent by wolle February 7
• A5S doesn't like to feed filament, even at higher temps

  58 views 6 comments 0 points Most recent by Samuel Pinches February 3
• A5S dead after 2 years: buzzer, heater and dark screen

  55 views 10 comments 0 points Most recent by Matt February 2
• jgaurora A5S, defective electrical control

  34 views 3 comments 0 points Most recent by Samuel Pinches January 27
• Understanding Z-offset in custom firmware

  55 views 2 comments 0 points Most recent by Steve January 15
• Z axis not moving, even swapping the stepper drivers

  41 views 0 comments 0 points Most recent by Giuseppe January 14
• A5S - X axis problem starting print at wrong place

  33 views 1 comment 0 points Most recent by Samuel Pinches December 2020
• New---Having some trouble ever since I replaced filament

  35 views 2 comments 0 points Most recent by Samuel Pinches December 2020
• No Extrusion

  45 views 2 comments 0 points Most recent by giantrobot2001 December 2020