Getting Started & Troubleshooting

Discussion List

• A5 even more problems now with community firmware?

  108 views 1 comment 0 points Most recent by Samuel Pinches November 2018
• Z axis move and stop

  64 views 0 comments 0 points Started by Fieldy November 2018
• Started printing with the A5, problems with new firmware and stepper drivers.

  345 views 18 comments 0 points Most recent by Prokktor November 2018
• Strange problem with A5 (only when USB connected)

  120 views 0 comments 0 points Started by Manu1001 November 2018
• Many Problems with the A5

  1.2K views 50 comments 0 points Most recent by jirgel November 2018
• spare parts

  230 views 2 comments 0 points Most recent by Matt November 2018
• Warping Problems

  662 views 42 comments 0 points Most recent by netzmark November 2018
• Strange First Layer Printing Problems

  471 views 21 comments 0 points Most recent by Prokktor November 2018
• JGAURORA A5 - A very disappointing 3D Printer

  3.2K views 37 comments 0 points Most recent by netzmark November 2018
• Cura 3.6.0 on my A5.......im impressed

  387 views 4 comments 0 points Most recent by sasa November 2018
• Distance between nozzle and heatbed after leveling

  1.3K views 64 comments 0 points Most recent by cybercow November 2018
• What in the is causing this noise

  500 views 12 comments 0 points Most recent by itisnot_me November 2018
• Fan doesn't turn on automatically

  126 views 3 comments 0 points Most recent by Prokktor November 2018
• Back half of model lifted off bed

  64 views 3 comments 0 points Most recent by Auswanderer November 2018
• A5 setep motor error

  85 views 3 comments 0 points Most recent by Samuel Pinches November 2018
• Power suply

  40 views 2 comments 0 points Most recent by Samuel Pinches November 2018
• A5 Rocker Power Switch will not move to off position.

  257 views 5 comments 0 points Most recent by Clintor24 November 2018
• Can't heat hot end (Error Heating Failed...)

  122 views 1 comment 0 points Most recent by Samuel Pinches November 2018
• My X- Y- axis completely out (TMC2130 V1.1 (NEW SPI Version) Stepper Motor Drivers )

  360 views 4 comments 0 points Most recent by Samuel Pinches November 2018
• extruder motor clicking

  509 views 4 comments 0 points Most recent by Robert November 2018
• Blackened plastic oozing from nozzle

  140 views 2 comments 0 points Most recent by Prokktor November 2018
• below a .2mm layer height

  232 views 5 comments 0 points Most recent by Prokktor November 2018
• Repeated movement with no extrusion

  75 views 3 comments 0 points Most recent by Samuel Pinches November 2018
• Problems getting a good print, poor quality and looks terrible.

  1.6K views 38 comments 0 points Most recent by DIYglenn November 2018
• More Noob questions: My BRIM is curling and tolerance problems:

  1.1K views 12 comments 0 points Most recent by Samuel Pinches November 2018
• A5 bed heater cycling

  151 views 5 comments 0 points Most recent by Jamal3f November 2018
• Supports in cura

  653 views 8 comments 0 points Most recent by sasa November 2018
• extruder

  250 views 47 comments 0 points Most recent by Matt November 2018
• Cant get this thing to extrude for the life of me

  105 views 3 comments 0 points Most recent by Neebles November 2018
• Print Settings

  182 views 1 comment 0 points Most recent by itisnot_me November 2018