Getting Started & Troubleshooting

Discussion List

• A5 LCD flashing "Booting..." and beeping at the same time.

  163 views 1 comment 0 points Most recent by Samuel Pinches July 2018
• Help with print settings

  753 views 1 comment 0 points Most recent by Samuel Pinches July 2018
• Bed Leveling Screws/Springs - Very Tight... stripping knobs

  534 views 2 comments 0 points Most recent by Nitro66215 July 2018
• not extruding anything

  1.5K views 11 comments 0 points Most recent by seafian July 2018
• Temp froze on screen

  76 views 1 comment 0 points Most recent by Samuel Pinches July 2018
• Reverse axis and general troubleshooting TMC2130 v1.1

  527 views 2 comments 0 points Most recent by Ophiocos July 2018
• A5 Nozzle temperature reads -15 degrees

  702 views 23 comments 0 points Most recent by dandan July 2018
• Nozzle way off the bed after nozzle change

  275 views 4 comments 0 points Most recent by Samuel Pinches July 2018
• Heated bed not working

  216 views 13 comments 0 points Most recent by AETEK July 2018
• a few questions

  69 views 0 comments 0 points Started by nach00 July 2018
• Bed leveling mesh not applying

  482 views 10 comments 0 points Most recent by Samuel Pinches July 2018
• Absolute tangled mess misprints... what’s up!?

  332 views 1 comment 0 points Most recent by Samuel Pinches July 2018
• Getting rid of z-seam and underextrusion

  4.8K views 11 comments 0 points Most recent by Samuel Pinches July 2018
• Brand new A5 - front-panel DOA?

  83 views 3 comments 0 points Most recent by Samuel Pinches July 2018
• Z-axis not moving at all

  1.6K views 20 comments 0 points Most recent by seafian July 2018
• What are the two thin wires connected near the nozzle?

  276 views 16 comments 0 points Most recent by Samuel Pinches July 2018
• can't save bed leveling data

  627 views 2 comments 0 points Most recent by davidtriune July 2018
• Error in the documentation for the MKS TFT2.8

  197 views 1 comment 0 points Most recent by Samuel Pinches July 2018
• Touch panel "debouncing"

  418 views 2 comments 0 points Most recent by seafian July 2018
• PETG prints stops after a while

  637 views 8 comments 0 points Most recent by Samuel Pinches July 2018
• The pinout designations of the MKS-GEN_L 1.0 documentation are partly faulty

  7.7K views 2 comments 0 points Most recent by AETEK July 2018
• Y axis issues / bed nut impacting on base

  91 views 1 comment 0 points Most recent by jollypike July 2018
• full size prints 300mm x 300mm x 300mm , speed ???

  100 views 3 comments 0 points Most recent by Samuel Pinches June 2018
• Extruder preheat sets to 0 when trying to print

  78 views 1 comment 0 points Most recent by Samuel Pinches June 2018
• Is this Layer Shift? Recommendations on how to fix?

  664 views 1 comment 0 points Most recent by Samuel Pinches June 2018
• Y is going crazy

  159 views 2 comments 0 points Most recent by Samuel Pinches June 2018
• cleaning the bed

  590 views 1 comment 0 points Most recent by Samuel Pinches June 2018
• Why do the thermistor inputs break sometimes?

  1.4K views 5 comments 0 points Most recent by AETEK June 2018
• problems with Y and Z axes

  233 views 4 comments 0 points Most recent by Samuel Pinches June 2018
• New A5 Reboots when preheating bed for leveling

  163 views 11 comments 0 points Most recent by Samuel Pinches June 2018