Getting Started & Troubleshooting

Discussion List

• Warning: Heated Bed Power Clamps

  1K views 10 comments 0 points Most recent by Alex October 2018
• Money Cat from USB fine, but nothing else sticks to bed

  238 views 3 comments 0 points Most recent by Alex October 2018
• Ugly prints, stringing, bad walls, bad top layers

  506 views 3 comments 0 points Most recent by MakeCents October 2018
• Poor printing quality

  158 views 2 comments 0 points Most recent by Flo1988 October 2018
• NOT EXTRUDING

  271 views 4 comments 0 points Most recent by Michael Horgan October 2018
• My printer won't go to home anymore.

  387 views 3 comments 0 points Most recent by Samuel Pinches October 2018
• Strange underextrusion after power failure

  210 views 6 comments 0 points Most recent by Samuel Pinches October 2018
• A5 won’t implement mesh the previous level

  93 views 2 comments 0 points Most recent by Simon September 2018
• Extruder motor question

  82 views 2 comments 0 points Most recent by rhaub101 September 2018
• Loose x-axis coupling and other annoyances

  163 views 1 comment 0 points Most recent by delirii September 2018
• weird layer issue...

  102 views 1 comment 0 points Most recent by Samuel Pinches September 2018
• Extruder clicking noise at retracts and when changing filament

  741 views 5 comments 0 points Most recent by allengregoryiv September 2018
• Calibration cube to big

  364 views 1 comment 0 points Most recent by Gonzo September 2018
• Spring supports....opinions?

  277 views 16 comments 0 points Most recent by Samuel Pinches September 2018
• printing in the bottom left corner (a5)

  99 views 1 comment 0 points Most recent by Samuel Pinches September 2018
• Change max retraction speed in community firmeare

  243 views 1 comment 0 points Most recent by Samuel Pinches September 2018
• Heating failed, Heatbed

  181 views 10 comments 0 points Most recent by Tim92 September 2018
• Printing is automatically paused - need HELP!

  710 views 5 comments 0 points Most recent by hver September 2018
• Keep your eyes open when filament buying

  188 views 3 comments 0 points Most recent by lsh60 September 2018
• A5 bed replacement

  244 views 0 comments 0 points Started by sasa September 2018
• Change filament mid print

  1.1K views 4 comments 0 points Most recent by Samuel Pinches September 2018
• Wobbely wobbely - need advice on....no clue what I'm looking at...

  144 views 3 comments 0 points Most recent by wolph42 September 2018
• Please Diagnose my symptoms

  262 views 10 comments 0 points Most recent by Samuel Pinches September 2018
• Print Resume Feature

  347 views 2 comments 0 points Most recent by Samuel Pinches September 2018
• Left z axis lead screw gets stuck

  1.1K views 2 comments 0 points Most recent by DIYglenn September 2018
• Cura - fine setting - no bed adhesion

  592 views 2 comments 0 points Most recent by wolph42 September 2018
• My A5 stopped in the middle of a print, no problems found.

  83 views 0 comments 0 points Started by DIYglenn September 2018
• Throat(Tube) broken inside the heatsink (x-axis holder)

  913 views 3 comments 0 points Most recent by Printok September 2018
• What is the screw size that holds the extruder fan duct in place?

  246 views 2 comments 0 points Most recent by Samuel Pinches September 2018
• LCD Panel will not operate printer

  111 views 3 comments 0 points Most recent by Samuel Pinches September 2018