Getting Started & Troubleshooting

Discussion List

• Heatbreak for A5

  834 views 2 comments 0 points Most recent by AETEK June 2018
• Extruder and Bed same temp problems

  579 views 47 comments 0 points Most recent by Ophiocos June 2018
• Firmware Upgrade

  311 views 3 comments 0 points Most recent by Samuel Pinches June 2018
• Bed Temp after Printing

  210 views 7 comments 0 points Most recent by Samuel Pinches June 2018
• Stepper Driver: Y driver error detected

  166 views 2 comments 0 points Most recent by Hevilp June 2018
• Possible to print without filament?

  75 views 2 comments 0 points Most recent by Hevilp June 2018
• print pop off plate during resume on A5

  196 views 4 comments 0 points Most recent by enochroot June 2018
• Glass Released from heat element

  110 views 4 comments 0 points Most recent by Hevilp May 2018
• A5 motors are not moving after repairing fried MKS board

  473 views 9 comments 0 points Most recent by Samuel Pinches May 2018
• Neverending Story extruder

  210 views 2 comments 0 points Most recent by Hevilp May 2018
• Thermistor

  886 views 12 comments 0 points Most recent by Samuel Pinches May 2018
• Many functions are not responding.

  115 views 6 comments 0 points Most recent by Luka May 2018
• How-To: Resume stopped print (with Repetier Server)

  514 views 1 comment 0 points Most recent by Samuel Pinches May 2018
• Layer Shift

  160 views 2 comments 0 points Most recent by g_pwn May 2018
• New A5...No Files Found

  706 views 2 comments 0 points Most recent by TapNorX May 2018
• GRID_MAX doesnt affect

  81 views 2 comments 0 points Most recent by Hevilp May 2018
• Isolation of thermistor

  110 views 2 comments 0 points Most recent by Hevilp May 2018
• Hotend is full of filament

  581 views 11 comments 0 points Most recent by Robert May 2018
• Which Slicer do you use?

  1.3K views 5 comments 0 points Most recent by Robert May 2018
• Damage to black coating on build plate.

  386 views 1 comment 0 points Most recent by Robert May 2018
• Stops printing mid print

  1.4K views 12 comments 0 points Most recent by Samuel Pinches May 2018
• Just added the A5 to my collection

  75 views 0 comments 0 points Started by Ap3rc0 May 2018
• A3S HOME does not work

  122 views 11 comments 0 points Most recent by Samuel Pinches April 2018
• Sometimes filament is not going properly out

  523 views 13 comments 0 points Most recent by djaurora April 2018
• Re-burning bootload on A5

  272 views 21 comments 0 points Most recent by Samuel Pinches April 2018
• Higher support (~>3cm fails) and displacement

  133 views 5 comments 0 points Most recent by Hevilp April 2018
• JGaurora a5 making a loud squeaking noise!

  327 views 1 comment 0 points Most recent by Samuel Pinches April 2018
• Temperature issues with the A5

  155 views 1 comment 0 points Most recent by Samuel Pinches April 2018
• WARNING - Jgaurora A3S, bought from Gearbest, was a real BAD DEAL

  409 views 9 comments 0 points Most recent by jollypike April 2018