Getting Started & Troubleshooting

Discussion List

• Many Problems with the A5

  1.2K views 50 comments 0 points Most recent by jirgel November 2018Getting Started & Troubleshooting
• A5 Rocker Power Switch will not move to off position.

  254 views 5 comments 0 points Most recent by Clintor24 November 2018Getting Started & Troubleshooting
• Problems with printing

  201 views 6 comments 0 points Most recent by Matt November 2018Getting Started & Troubleshooting
• printing issue

  103 views 3 comments 0 points Most recent by Matt October 2018Getting Started & Troubleshooting
• Getting Prints to stick

  101 views 3 comments 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• remove bowden coupler

  349 views 6 comments 0 points Most recent by Matt October 2018Getting Started & Troubleshooting
• BLTouch automatic leveling "loosing" max X one in 3 times?

  48 views 0 comments 0 points Started by SkacikPL October 2018 Getting Started & Troubleshooting
• Octolapse settings

  252 views 2 comments 0 points Most recent by Richy_T June 2019Getting Started & Troubleshooting
• Layer shift

  134 views 1 comment 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• Wax filament resistance

  72 views 1 comment 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• couple of questions

  155 views 16 comments 0 points Most recent by Matt October 2018Getting Started & Troubleshooting
• unresponsive firmware

  173 views 2 comments 0 points Most recent by eddymcfly October 2018Getting Started & Troubleshooting
• Weird First Layer Sometime

  119 views 3 comments 0 points Most recent by itisnot_me October 2018Getting Started & Troubleshooting
• JGAURORA A5 Bed + Kapton Tape?

  93 views 1 comment 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• Wrong distance below 10mm on Z axis

  105 views 2 comments 0 points Most recent by Tim92 October 2018Getting Started & Troubleshooting
• Bed leveling/adhesion issues

  155 views 1 comment 0 points Most recent by itisnot_me October 2018Getting Started & Troubleshooting
• extruder

  250 views 47 comments 0 points Most recent by Matt November 2018Getting Started & Troubleshooting
• Print Settings

  182 views 1 comment 0 points Most recent by itisnot_me November 2018Getting Started & Troubleshooting
• z axis not moving at all after even adjusting the stepper driver currents

  120 views 1 comment 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• ABS Print not sticking to heated bed

  128 views 1 comment 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• USB no files found

  113 views 4 comments 0 points Most recent by re3redo1 October 2018Getting Started & Troubleshooting
• Anybody using cura 3.5?

  145 views 2 comments 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• Ugly prints, stringing, bad walls, bad top layers

  502 views 3 comments 0 points Most recent by MakeCents October 2018Getting Started & Troubleshooting
• Bed Just Not Heating

  205 views 6 comments 0 points Most recent by sasa October 2018Getting Started & Troubleshooting
• Flashing new bootloader

  2.4K views 9 comments 0 points Most recent by 1980ace October 2018Getting Started & Troubleshooting
• My printer won't go to home anymore.

  382 views 3 comments 0 points Most recent by Samuel Pinches October 2018Getting Started & Troubleshooting
• Burning / Smoking Heated Bed Connector

  1.2K views 28 comments 0 points Most recent by Samuel Pinches November 2018Getting Started & Troubleshooting